Normally this is suppressed but you can turn this feature on here. Generally FlyQ defaults to taking off from the home airport you’ve specified. Be sure not to plan for Jet Airways if the selected aircraft cannot fly above FL Unless otherwise stated, FlyQ will plan flights with just one person, the pilot, onboard. Normally FlyQ calculates a flight plan based entirely on your takeoff and landing airports. If you fly such a plane, enter an appropriate value here or use the Defaults button in Settings to specify your preference.
|License:||For Personal Use Only|
|iPhone 5, 5S resolutions||640×1136|
|iPhone 6, 6S resolutions||750×1334|
|iPhone 7, 7 Plus, 8, 8 Plus resolutions||1080×1920|
|Android Mobiles HD resolutions||360×640, 540×960, 720×1280|
|Android Mobiles Full HD resolutions||1080×1920|
|Mobiles HD resolutions||480×800, 768×1280|
|Mobiles QHD, iPhone X resolutions||1440×2560|
|HD resolutions||1280×720, 1366×768, 1600×900, 1920×1080, 2560×1440, Original|
If you enter an airway, the router will ignore your Routing setting and just plan along the specified desktopp s. When FlyQ requests a DUAT weather briefing or files a flight plan, it uses the credentials associated with the selected pilot. Enter a higher or lower value as desired. Show altitude change points: Select Off to disable this feature.
AOPA Solid Wood Hot Pot Table with Burnt Stone Desktop Z80
Planning via GPS Direct tells FlyQ to create as direct as possible flight between the From and To airports but apply rules for terrain avoidance and wind-optimization. Aspen Avionics makes the Evolution glass panel system. Generally FlyQ defaults to taking off from the home airport you’ve specified.
If you fly such a plane, enter an appropriate value here or use deektop Defaults button in Settings to specify your preference.
When FlyQ says that it cannot compute the flight plan, it generally means that some of your input parameters conflict. Enter a different value in this field.
March AOPAversity Audio Conference
For some aircraft, typically jets or very high-performance pistons, it’s economically impractical to fly below a certain altitude regardless of the effects of winds. This is also used when filing the flight plan via DUAT.
Normally FlyQ calculates a flight plan based entirely on your takeoff and landing airports. When you see this error message, please use the More button to set or review your inputs. Unless otherwise stated here, FlyQ will assume your plane takes off with a full tank of fuel. Many pilots fly more than one plane so FlyQ lets you create as many aircraft profiles as you like. By tapping the More button at the top of the screen, you can control additional routing parameters.
Optimize for best winds: FlyQ allows you to create as many different pilots associated with your account as you like. Change your home airport by tapping the Settings button then tapping the Defaults button in the Flight Planning section. Use the Recent button to select from a list of airports you’ve recently used. Unless otherwise stated, FlyQ will plan flights with just one person, the pilot, onboard.
Normally FlyQ uses wind-optimization to plan the fastest flight possible by potentially going up to the service ceiling of your aircraft.
AOPA Solid Wood Hot Pot Table with Burnt Stone Desktop
Use this field to enter a specific altitude MSL either higher or lower than the service ceiling. For airways, you can choose between Victor Airways lower than 18, ft. Plans can be created whether you’re connected to the Internet or not but some advanced features are only available when online. Normally this desktkp suppressed but you can turn this feature on here.
Change your default setting from appa using the Defaults button within the Settings tab.
Add multiple route entries by separating them with a deskto e. In the Settings tab, tap the Aircraft button to add or edit aircraft profiles. Normally FlyQ will use the winds-aloft forecast for your flight time to plan the best altitude for the flight. Use this field to specify any intermediary waypoints, navaids, or airports by ident.
Enter the airport ident either with or without the ‘K’its name or even the city. When using JetA, the fuel value should be entered as pounds lbsotherwise the system uses gallons.